• Kontak Kami
  • Hotline : 08121314327 (WhatsApp)
  • SMS : 08121314327 (WhatsApp)

Kontak Kami

( pcs) Checkout

Toko Offline Jakarta : Jl. Tanjung No. 14, Jati Pulo, Palmerah, Jakarta Barat Toko Offline Surabaya : Jl. Gebang Lor No.29 (dekat Bundaran Kampus ITS) Toko Offline Bandung : Jl. Aceh No.24A Pasar Besi Kebon Sirih Toko Online : jualarduino.com WA 08121314327
Beranda » Sensor & Tranducer » SHT30-D Temperature AND Humidity Sensor Breakout Weather I2C Protocol

SHT30-D Temperature AND Humidity Sensor Breakout Weather I2C Protocol

Ditambahkan pada: 28 Juni 2018 / Kategori:
Kode : -
Berat : 5 gram
Stok : Ready Stock (100 pcs)
Dilihat : 8 kali
Review : Belum ada review
Rp 120.000
Tentukan Pilihan!
Pesan melalui SMS? Klik SMS
Bayar di tempat? Klik COD

Bagikan informasi tentang SHT30-D Temperature AND Humidity Sensor Breakout Weather I2C Protocol kepada teman atau kerabat Anda.

Deskripsi SHT30-D Temperature AND Humidity Sensor Breakout Weather I2C Protocol

Deskripsi Produk

Description:

Sensiron Temperature Humidity sensors are some of the finest & highest-accuracy devices you can get. And, finally we have some that have a true I2C interface for easy reading. The SHT30-D sensor has an excellent 2% relative humidity and 0.3C accuracy for most uses.

Unlike earlier SHT sensors, this sensor has a true I2C interface, and (bonus!) even with two address options. It also is 3V or 5V compliant, so you can power and communicate with it using just about any microcontroller or microcomputer.

Such a lovely chip – so we spun up a breakout board with the SHT30-D and some supporting circuitry such as pullup resistors and capacitors. Each order comes with one fully assembled and tested PCB breakout and a small piece of header. You’ll need to solder the header onto the PCB but it’s fairly easy and takes only a few minutes even for a beginner.

Power Pins:
Vin – this is the power pin. The chip can use 2.5-5VDC for power. To power the board, give it the same power as the logic level of your microcontroller – e.g. for a 5V micro like Arduino, use 5V. For a 3.3V controller like a Raspbery Pi, connect to 3.3V
GND – common ground for power and logic

I2C Logic pins:
SCL – I2C clock pin, connect to your microcontrollers I2C clock line.
This pin has a 10K pullup resistor to Vin
SDA – I2C data pin, connect to your microcontrollers I2C data line.
This pin has a 10K pullup resistor to Vin

Other Pins:
ADR – This is the I2C address selection pin. This pin has a 10K pull down resistor to make the default I2C address 0x44. You can tie this pin to Vin to make the address 0x45
RST – Hardware reset pint. Has a 10K pullup on it to make the chip active by default. Connect to ground to do a hardware reset!
ALR – Alert/Interrupt output. You can set up the sensor to alert you when an event has occured. Check the datasheet for how you can set up the alerts

 

Belum ada review untuk SHT30-D Temperature AND Humidity Sensor Breakout Weather I2C Protocol

Silahkan tulis review Anda

Alamat email Anda tidak akan dipublikasikan. Ruas yang wajib ditandai *

*







SIDEBAR